bootmod3 CustomROM now available for N55-EWG engine vehicles!
All the features and customization previously released for the S55 including MapSwitching, Flex Fuel, Antilag, Live Adjust burble and ethanol override, In-dash ethanol check and others are now available for the N55-EWG cars. This work starting with the S55 has been under way since last year and we are really excited to have it finally released on the N55-EWG as well!
bootmod3’s integrated Map Editor features 4300+ calibration tables available on the N55-EWG CustomROM for custom tuners on the platform to take advantage of. Advanced logging (RAM) channels support has also been expanded to include many new loggable parameters, many of which are exclusive to bootmod3 software customization.
New Stage 1, Stage 2 and Stage 2+ OTS maps are now also available featuring 4 integrated map slots, flex fuel, antilag and all the CustomROM features. Stage 2+ Multimap OTS map, with the presence of a Flex Fuel Sensor, scales all the way up to full E85 content fuels for those with upgraded HPFPs installed that can flow the required fuel volumes.
The most comprehensive bootmod3 software update is finally here and we are delighted to share it with everyone. Multiple features have been in development since mid 2020, many of which have been demo-ed to public throughout the time we were developing them. In December 2020 we completed development on the pre 2019 software S55s. We decided to finish 2019+ support as well and release it all together. It has endured a considerable delay from the initially planned release but we’ve managed to cover everything and in the process add even more functionality to the Map Editor and cover testing more extensively.
Our first release of the bootmod3 CustomROM is now ready for the S55 engine vehicles while we continue to work on adding these features to other vehicles in the bootmod3 lineup. Changes done for the S55 are being ported to the N55 vehicles followed by the B58.
To read about the bootmod3 CustomROM features available on the S55 engine refer to document below:
In the previous two videos we demonstrated bootmod3's new custom code features integrated into the factory DME (ECU), namely on-the-fly map switching and rolling antilag, both of which are using steering wheel controls for triggers allowing users to flash the car once and then select between any 4 maps that can be custom tuned to suit your modifications, octane and racing needs and to spool the turbo without using brake boosting and slightshot your way forward when racing :)
In this video we're demonstrating another new tuning feature that is in the works by the bootmod3 dev team called FLEX FUEL. bootmod3 Flex Fuel integration is a set of custom tables predefined to tune your vehicle for dynamic aggression/power in the tune based on input from a Flex Fuel sensor. In this case we're using a Continental flex fuel sensor with a Zeitronix ECA2 kit which sends Flex Sensor's data over the CANBus which the DME handles in real-time to make the tune more or less aggressive based on ethanol % in the fuel. We previously made map switching on-demand work using the steering wheel controls. Now, there's a new option to also enable Flex Fuel in the tune and define separate tables for tuning for ignition, fuel, load/torque, various safeties, and many others. Tuning details behind getting a flex fuel tune working are also very straightforward and very powerful. A tuner defines your base map or maps (1 through 4) which you can select through the steering wheel (example: Map1: Stage 1 93 map, Map 2: Stage 2 93 octane, Map3: Stage 2+ 98 octane, Map 4: Stage 2+ race gas) . Any or all of the 4 switchable maps can now be configured as ENABLED for Flex Tuning. When enabled, data from the Flex Fuel Sensor is used to scale between say a pump gas E0 (no ethanol tune, or E10) to a full E85 or E100 (100% ethanol) tune. If sensor detects no ethanol then the scaling leaves the base maps alone without scaling them upwards in aggression. If the sensor detects and sends say 50% ethanol to the DME then the DME can be set to change ignition, fuel, load/torque and many other tables to increase power levels due to ethanol's much higher octane over petrol/gasoline.
In this demo, we're demonstrating on a 2015 BMW F80 M3 which starts out with a 20% ethanol blend in the tank. Those that enjoy the details can see the blend factors are set for 0.50 for this ethanol level just as an example. Currently there are 3 main blend factor tables, ignition, fuel and torque, and they can be individually used to scale among many tables required for tuning Flex Fuel, from cold starting the car with full ethanol in the tank to full on power. In the end of the video we add some more alcohol and you can see in the bootmod3 dashboard how the Flex % goes upwards from 20% to 27% as the fuel system catches up and the fuel in the tank gets a chance to blend as it isn't instant.
Really excited to show a render of the bootmod3 board undergoing firmware development. This board measures just 80mm by 50mm and already packs a heavy punch!
Board currently has multiple inputs (frequency and analog) and features CANBus integration and WiFi/BT for configurability. Rev2 of the board will also feature various outputs for activating/deactivating external aux systems (e.g. port injection, nitrous, etc), tuning it via tables integrated in the new bootmod3 editor.
Purpose of this board is to expand I/O capabilities of the factory engine computer (DME) and allow it to integrate with external sensors not already available on these cars (e.g. flex fuel sensor, meth flow/level sensor, port injection fuel injector duty, etc) and provide that data over CANBus to the DME for various tuning strategies. Any 3rd party products that support similar CANBus integration are also supported by bootmod3 (e.g. Zeitronix CANBus ECA2 flex sensor kit, etc). Integrating meth flow/tank level sensor data is a nice one and will allow for similar tuning strategies and failsafes as with flex fuel.
For this new demo we've managed to move controls for map switching to the steering wheel cruise buttons. You activate it by pressing the Resume button, and switching among 4 map slots (expandable if needed at a future date) by using the up/down button that are typically used to increase/decrease speed when cruise control is active. OEM cruise control functionality remains in tact and map switching can be done with the engine off, on and while driving.
This video was done on our 2015 F80 M3 with the MEVD17.2.G DME and applies to all S55 engine vehicles. Support for these features is in progress for all other vehicle models bootmod3 supports today.
Enjoy the vid while we continue making progress with many other advanced tuning features such as BM3 FlexFuel, Antilag and many others. Cheers!